Recherche avancée

Sur d’autres sites (6095)

• Write two webcam video with avconv

  16 août 2014, par Jones

  Have problem capture video with avconv

  I using this commands video0 in shell 0 and video1 in shell 1

  avconv -f video4linux2 -i /dev/video0 video0.avi
  
  avconv -f video4linux2 -i /dev/video1 video1.avi

  But with start second video recorder message

  /dev/video1 : No space left on device

  Question there is the possibility of recording two videos simultaneously ?

  Other

  First capture of video0.avi is work perfectly, but if I interrupt with Ctrl+C and try execute same command the video is not captured.

  This message displayed in shell

  uvcvideo : Failed to resubmit video URB (-27)

  The process still running ?

  Removing webcam and reconnect work fine in first time.

• H.264 conversion with FFmpeg (from a RTP stream)

  12 juillet 2014, par Toby

  Environment :

  I have an IP Camera, which is capable of streaming it’s data over RTP in a H.264 encoded format. This raw stream is recorded from the ethernet. With that data I have to work.

  Goal :

  In the end I want to have a *.mp4 file, which I can play with common Media Players (like VLC or Windows MP).

  What have I done so far :

  I take that raw stream data I have and parse it. Since the data has been transmitted via RTP I need to take care of the NAL Bytes, SPS and PPS.

  1. Write a raw file

  First I determine the type of each frame received over Ethernet. To do so, I parse the first two bytes of every RTP Payload, so I can get the 8 NAL Unit Bit, the Fragment Type Bits and the Start, Reserved and End Bit. In the payload, they’re arranged like this :

  Byte 1: [          3 NAL Unit Bits          | 5 Fragment Type Bits]
  
  Byte 2: [Start Bit | Reserved Bit | End Bit | 5 NAL Unit Bits]

  From this I can determine :

  • Start and End of
    a Video Frame -> Start Bit and End Bit
  • Type of the Payload -> 5 Fragment Type Bits
  • NAL Unit Byte

  The Fragment types which are necessary in my case are :

  Fragment Type  7 = SPS
  
  Fragment Type  8 = PPS
  
  Fragment Type 28 = Video Fragment

  The NAL Byte is created by putting the NAL Unit Bits from Byte 1 and 2 together.

  Now depending on the fragmentation type I do the following :

  SPS/PPS :

  1. Write the NAL Prefix (0x00 0x00 0x01) and then the SPS or PPS data

  Fragmentation with Start Bit

  1. Write NAL Prefix
  2. Write NAL Unit Byte
  3. Write remaining raw data

  Fragmentation without Start Bit

  1. Write raw data

  This means my raw file looks something like this :

  [NAL Prefix][SPS][NAL Prefix][PPS][NAL Prefix][NAL Unit Byte][Raw Video Data][Raw Video Data]....[NAL Prefix][NAL Unit Byte][Raw Video Data]...

  For every PPS and SPS I find in my stream data, I just write a NAL Prefix ( 0x00 0x00 0x01 ) and then the SPS/PPS itself.

  Now I can’t play this data with some media player, which leads me to :

  2. Convert the file

  Since I wanted to avoid working much with codecs I just went to use an existing application -> FFmpeg. This I am calling with those parameters :

  ffmpeg.exe -f h264 -i <rawinputfile> -vcodec copy -r 25 <outputfilename>.mp4</outputfilename></rawinputfile>

  -f h264 : This should tell ffmpeg I have a h264 coded stream

  -vcodec copy : Quote from the manpage :

  Force video codec to codec. Use the "copy" special value to tell that the raw codec data must be copied as is.

  -r 25 : Sets the framerate to 25 FPS.

  When I call ffmpeg with those parameters I get an .mp4 File, which I can play with VLC and Windows MP, so it actually works. But the file now looks a bit different from my raw file.

  This leads me to my question :

  What did I actually do ?

  My problem is not that it is not working. I just want/need to know what I have actually done with calling ffmpeg. I had a raw H264 file which I could not play. After using FFmpeg I can play it.

  There are the following differences between the original raw file (which I have written) and the one written by FFmpeg :

  1. Header : The FFmpeg File has like about 0x30 Bytes of Header
  2. Footer : The FFmpeg File also has a footer
  3. Changed Prefix and 2 new Bytes :

  While a new Video Frame from the Raw File started like
  [NAL Prefix][NAL Unit Byte][Raw Video Data] in the new file it looks like this :

  [0x00 0x00][2 "Random" Bytes][NAL Unit Byte][Raw Video Data].....[0x00 0x00[2 other "Random" Bytes][NAL Unit Byte][Raw Video Data]...

  I understand that the Video Stream needs a container format (correct me if I am wrong but I assume that the new header and footer are responsible for that). But why does it change actually some Bytes in the raw data ? It can’t be some decoding since the stream itself should get decoded by the player and not ffmpeg.

  As you can see I don’t need a new solution for my problem as far more an explanation (so I can explain it by myself). What does ffmpeg actually do ? And why does it change some bytes within the video data ?

• How to convert Live video stream from YUV(HDYC) to RGB

  9 août 2013, par user2499628

  I want to convert video streams from webcam. that video streams are called HDYC. I think it's a little special so I didn't control now.

  My question is How to convert that format to rgb in c++ using ffmpeg ? but there are some constraints.
  I don't want to make a file. in other wors, It needs to convert video streams from webcam. also It's a real time operation.

  Thanks.