Recherche avancée

Sur d’autres sites (5705)

• vc-1 : Optimise parser (with special attention to ARM)

  23 avril 2014, par Ben Avison

  vc-1 : Optimise parser (with special attention to ARM)
  The previous implementation of the parser made four passes over each input
  
  buffer (reduced to two if the container format already guaranteed the input
  
  buffer corresponded to frames, such as with MKV). But these buffers are
  
  often 200K in size, certainly enough to flush the data out of L1 cache, and
  
  for many CPUs, all the way out to main memory. The passes were :
  1) locate frame boundaries (not needed for MKV etc)
  
  2) copy the data into a contiguous block (not needed for MKV etc)
  
  3) locate the start codes within each frame
  
  4) unescape the data between start codes
  After this, the unescaped data was parsed to extract certain header fields,
  
  but because the unescape operation was so large, this was usually also
  
  effectively operating on uncached memory. Most of the unescaped data was
  
  simply thrown away and never processed further. Only step 2 - because it
  
  used memcpy - was using prefetch, making things even worse.
  This patch reorganises these steps so that, aside from the copying, the
  
  operations are performed in parallel, maximising cache utilisation. No more
  
  than the worst-case number of bytes needed for header parsing is unescaped.
  
  Most of the data is, in practice, only read in order to search for a start
  
  code, for which optimised implementations already existed in the H264 codec
  
  (notably the ARM version uses prefetch, so we end up doing both remaining
  
  passes at maximum speed). For MKV files, we know when we’ve found the last
  
  start code of interest in a given frame, so we are able to avoid doing even
  
  that one remaining pass for most of the buffer.
  In some use-cases (such as the Raspberry Pi) video decode is handled by the
  
  GPU, but the entire elementary stream is still fed through the parser to
  
  pick out certain elements of the header which are necessary to manage the
  
  decode process. As you might expect, in these cases, the performance of the
  
  parser is significant.
  To measure parser performance, I used the same VC-1 elementary stream in
  
  either an MPEG-2 transport stream or a MKV file, and fed it through ffmpeg
  
  with -c:v copy -c:a copy -f null. These are the gperftools counts for
  
  those streams, both filtered to only include vc1_parse() and its callees,
  
  and unfiltered (to include the whole binary). Lower numbers are better :
                  Before          After
  
  File  Filtered  Mean   StdDev   Mean   StdDev  Confidence  Change
  
  M2TS  No        861.7  8.2      650.5  8.1     100.0%      +32.5%
  
  MKV   No        868.9  7.4      731.7  9.0     100.0%      +18.8%
  
  M2TS  Yes       250.0  11.2     27.2   3.4     100.0%      +817.9%
  
  MKV   Yes       149.0  12.8     1.7    0.8     100.0%      +8526.3%
  Yes, that last case shows vc1_parse() running 86 times faster ! The M2TS
  
  case does show a larger absolute improvement though, since it was worse
  
  to begin with.
  This patch has been tested with the FATE suite (albeit on x86 for speed).
  Signed-off-by : Michael Niedermayer <michaelni@gmx.at>
  

  • [DH] libavcodec/vc1_parser.c

• vp9 : don’t create special u/v filter masks for 444.

  30 avril 2015, par Ronald S. Bultje

  vp9 : don’t create special u/v filter masks for 444.
  This fixes vp91-2-04-yuv444.webm.
  

  • [DH] libavcodec/vp9.c

• Revision 60bd744c88 : Improve accuracy of rate control in CQ mode Modifies a special handling that im

  8 avril 2015, par Debargha Mukherjee

  Changed Paths :
   Modify /vp9/encoder/vp9_firstpass.c

  
  
  Improve accuracy of rate control in CQ mode

  Modifies a special handling that improves rate control accuracy in
  the constrained quality mode, when the undershoot and overshoot
  limits are set tighter.

  Change-Id : If62103f0ef3ed1cac92807400678c93da50cf046